平等36 beam axesGL-S36FH

GL-S36FH - Flat type 36 beam axes

Data Sheet (PDF)

Manuals

Specifications

Model				GL-S36FH
Type				平等
Detection capability				ø25 mmØ0.98“
Beam axis spacing				20 mm0.79"
Operating distance				0.1 to 2 m0.3' to 6.6'
Effective aperture angle				最大限度。±3.75° (when the operating distance is 2 m6.6')
光源				Infrared LED (870 nm)
Response time(ms)	Wire synchronization, one-line, or optical synchronization system (channel 0)	ON→OFF		8.3^*1
		→在		51.3^*2
	Optical synchronization system (channel A or B)	ON→OFF		11.6^*1
		→在		56.1^*2
奥斯经营				Turns on when no interruptions are present in the detection zone
发送器和接收器之间的同步				Optical synchronization or wire synchronization （由布线决定）
Light interference prevention function				Optical synchronization: prevented by Channel A and B with setting switch 电线同步：自动防止
Control output (OSSD output)	Output type			2晶体管输出 (PNP or NPN output is determined by the cable type.)
	最大限度。load current			最大限度。300 mA
	Residual voltage (when ON)			最大限度。2.5 V（电缆长度为5米16.4')
	OFF state voltage			最大限度。2.0 V (with a cable length of 5 m16.4')
	Leakage current			最大限度。200 µA
	最大限度。load capacitance			2.2 µF
	Load wiring resistance			最大限度。2.5 Ω
Inputs 1 and 2				Short-circuit current: approx. 1 mA
Power supply	Current consumption(mA)	当中心指示器打开时	Transmitter	48^*3
			接收者	73^*3
		When the center indicator is OFF	Transmitter	30^*3
			接收者	54^*3
	电源电压			24 VDC ±20%, ripple (P-P) 10% or less, Class 2
保护电路				Reverse current protection, short-circuit protection and surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 CLASSA，FCC PART15B Classa，ICE-003类
	安全			IEC61496-1，EN61496-1，UL61496-1（4型ESPE） IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508，EN61508（SIL3），IEC62061，EN62061（SIL CL3） EN ISO13849-1: 2015 (Category 4, PLe) UL508, UL1998 GB4584
Environmental resistance	Enclosure rating			IP65/IP67 (IEC60529)
	过电压类别			II
	Ambient light			Incandescent lamp: 3,000 lux or less, Sunlight: 20,000 lux or less
	Operating ambient temperature			-10到+ 50°C14 to 122 °F(No freezing)
	Storage temperature			-25 to +60 °C-13 to 140 °F(No freezing)
	Operating relative humidity			15 to 85 % RH (no condensation)
	Storage relative humidity			15 to 95 % RH
	抗振			10至55 Hz，双幅度0.7毫米0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s²(Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	主要单位案例			聚芳基酯
Weight	Transmitter			325 g
	接收者			330 g
^1如果响应时间（开关）超过20毫秒，本机不能用作基于中国标准GB 4584“触力机用光电耦合技术条件”的经过认证产品。当GL-S单元串联连接时，根据以下步骤计算响应时间; 1. Sum up the response time of all unit. 2. Subtract the following time from the result of previous step. ■→关闭 One sub unit connected: 2 ms Two sub units connected: 4.2 ms (When using Optical synchronization system and Channel A or B) One sub unit connected: 2.7 ms Two sub units connected: 5.7 ms ■ OFF→ON 一个子单元连接：42毫秒两个子单元连接：84毫秒 ^2如果响应时间（开关）超过20毫秒，本机不能用作基于中国标准GB 4584“触力机用光电耦合技术条件”的经过认证产品。当GL-S单元串联连接时，根据以下步骤计算响应时间; 1. Sum up the response time of all unit. 2. Subtract the following time from the result of previous step. ■→关闭 One sub unit connected: 2 ms Two sub units connected: 4.2 ms (When using Optical synchronization system and Channel A or B) One sub unit connected: 2.7 ms Two sub units connected: 5.7 ms ■ OFF→ON 一个子单元连接：42毫秒两个子单元连接：84毫秒 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^*3The control output (OSSD) current is not included. When inputs are turned ON, the current consumption increases by 1 mA per input.

Other Models